1600 Watt 24V Missouri Raptor G5 70" Diameter 3 Blade Freedom Wind Turbine

1600 Watt 24V Missouri Raptor G5 70" Diameter 3 Blade Freedom Wind Turbine

1600 Watt Missouri Raptor G5 70 Inch Diameter 3 Blade Freedom Wind Turbine

Our Missouri Freedom Wind Turbine components are hot dipped galvanized with zinc plated hubs!


Will not rust
No need for painting or special coating for up to 50 years under normal conditions

 

Low wind speed rated wind turbine for home, business, or remote use with the Freedom Permanent Magnet Generator™ (PMG) - 1600 Watts plus potential power!

Raptor G5 33 inch black carbon fiber blades self regulate their speed in high winds (also available in a 5 blade model).

Our newest innovation in power generation! 

Brand new Freedom Permanent Magnet Generator™ (PMG) - This is our highest amp model - Up to 1600 watts of output!  NO COGGING - Cut in wind speed of 6 MPH

 

Why buy a Freedom PMG™ over a Delco car alternator PMA?

The answer is simply more copper!  More copper equals more power - each Freedom PMG rotor contains twice as much copper than any Delco style PMA. 

Uses: Battery or battery bank charging, stackable wind turbine grid tie inverters, direct DC water heating elements, direct DC resistive heating, or other applications where 3 phase AC or DC can be used. 

Note: If you are replacing a DC output wind turbine with our 3 phase turbine and do not want to change your DC wiring then you can mount the bridge rectifier at the top of the tower for a DC run down.
 

Wind Turbine Features:

  • 1600 Watt Freedom PMG™ for efficient three phase power generation.
    • 3 phase bridge rectifier for converting to DC output.
    • (see below for more specifics)
  • Heavy duty hub spacer/stabilizer
  • PMG mounting bracket and heavy duty Stars & Stripes wind turbine tail
    • Mounting Bracket fits on 1.5" schedule #40 or #80 pipe (1 7/8" OD) and allows for easy turning
    • Tail fin measures 9 3/4 inches wide x 28 3/4 inches tall
      • Cut from 16 gauge steel
    • Hot dipped galvanized weather resistant finish
  • Zinc plated steel hub is 8 3/8 inch diameter and 1/4 inch thick
  • Comes with three Raptor G5 black carbon fiber composite blades
    • Aerodynamically tapered blades for maximum output
    • Each blade is 33 inches long
    • Assembled blades and hub makes 70 inch swept area
  • Overall length from blades to tail is 37 inches

No slip rings to fail or replace. Simple and effective, the turbine uses a wire tension system which will last a lifetime. The single power transmission cord never twists because the wind never spins the turbine around in the same direction hundreds of times. Typically, the wind only comes from two directions. It has yet to be an issue with any one of the thousands of turbines we have distributed.
 

Freedom PMG™ Features: 

  • NO COGGING - Cut in wind speed of 6 MPH
  • Comes with a heavy duty rectifier & hub spacer stabilizer
  • 17 mm Stainless steel shaft compatible with all Missouri Wind and Solar hubs
  • Polished aluminum case
  • Zinc plated 14 magnet rotor and skewed stator core
  • Specifically designed for wind turbines.
  • Fits delco bolt patterns and mounts up to our standard mounting bracket.

Freedom PMG Specifications:

  • 3/8" Diameter bolt holes
  • 1 15/16" on center between mounting holes
  • 5 7/8" OD Width
  • 6 5/16" Tall
Option 1

Ennis Wind & Solar

5030 SW McKinney St. 
 Rice, TX 75155

Tuesday thru Friday 8am to 6pm

Saturday 9am to 1pm

Closed Sunday and Monday

 903-872-2118

Division of:

Visit our other divisions of Ennis Products